Pay Dues or become a Site Supporter
|
Pay Dues or become a Site Supporter
|
|
|||||||
| Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here. |
 |
|
|
Thread Tools |
|
#1
September 12th, 2018, 01:10 AM
|
||||
|
||||
How does a slave cylinder go out?
How exactly does it feel when a slave cylinder finally goes out? Is the clutch/brake system all that complicated?
My clutch goes to the floor and stays there, but the reservoir is full. I know my slave cylinder is leaky (ordered a replacement already) but even leaky it still worked as long as I kept the tank full. Is there another thing that goes out on these things pretty often that I should check while I'm in there? 
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. 
|
|
#2
September 12th, 2018, 04:47 AM
|
|||
|
|||
|
Re: How does a slave cylinder go out?
Fetch, When the slave cylinder fails, the clutch won't release anymore. Your small leak probably just became a big leak and drew air into the system which means no more hydraulics to work the clutch. Check the line from the master cylinder to the slave cylinder. It has a rubber section which can also leak. Inline Tube sells a replacement line for $45 or you might have one made locally.
These trucks are not complicated compared to new ones. Of course when you add years of caked on grease, rusty bolts & nuts, wasps & mud daubers etc. things can get a little challenging. An original GMC service manual is worth the money too.
|
|
#3
September 13th, 2018, 07:12 PM
|
||||
|
||||
|
Re: How does a slave cylinder go out?
Air in the line was exactly what it was, thanks Snazzy! After a couple of days of having a full master cylinder gravity did its thing and my clutch works again!
I have a replacement slave cylinder on the way.
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy.
|
|
| Bookmarks |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 1970 RM7500 clutch slave cylinder question | WE7X | Transmissions and Rear Ends | 3 | October 6th, 2022 07:05 PM |
| Re: [6066 GMC] Slave Cylinder Bore Size | Archiver | Previous Forum Posts | 0 | January 5th, 2008 09:12 AM |
| Re: [6066 GMC] Slave Cylinder Bore Size | Archiver | Previous Forum Posts | 0 | January 5th, 2008 07:40 AM |
| Re: [6066 GMC] Slave Cylinder Bore Size | Archiver | Previous Forum Posts | 0 | January 5th, 2008 06:34 AM |
| [6066 GMC] Slave Cylinder Bore Size | Archiver | Previous Forum Posts | 0 | January 5th, 2008 04:43 AM |
